Philips TV does not respond to the remote and buttons

Ease of use of technology is always important for the user. If the remote control stops working, you need to know what needs to be done to restore its operation. To do this, first of all, it is necessary to determine the cause of what happened. If the user has the necessary knowledge, he can restore functionality as soon as possible. In this article, we will figure out why the Philips TV does not respond to the remote control, and sometimes the power buttons.
If the remote does not work, before looking for the cause, you need to check the following:

1. You need to make sure that the Philips TV is connected to the power supply . If you forgot about it earlier, the plug is plugged into the outlet.
2. You need to be sure that there is voltage in the network . Perhaps there was a power outage and this is what is causing the problems. To verify the presence of voltage, it is enough to turn on some electrical appliance in the network.
3. It is necessary to check the operation of the television receiver without using the remote control. To do this, you need to set various commands using the control panel and check that Philips Smart TV responds to buttons.

If the user sees that the electricity is on and the TV is working normally, then if the remote control malfunctions, it is necessary to understand the reasons and put it in order.

No response to old Philips remote

If the channels cannot be switched in only one way, it is easy to understand what exactly is broken. For example, when the remote does not work, but everything can be done from the TV, this gives reason to think that the TV’s receiving device is faulty. This problem is fixed only in the workshop. If the remote control works fine for a few minutes and then loses connection, then the most common cause is overheating of the processor, which is usually due to poor soldering.
If a signal is given to switch the channel, but it itself is delayed, then in this case it can be assumed that there are problems associated with the incorrect operation of the TV receiving device. Most often this is due to incorrectly working firmware.

What if the TV does not respond to the remote and buttons on the Philips TV, how to troubleshoot

This can happen for various reasons. If the remote control does not respond to button presses after prolonged use, then do the following:

1. It is necessary to check the presence of interference sources in the immediate environment . These can, for example, be sources of bright light, devices for fluorescent lighting. It is recommended to turn them off and try using the remote control. In some cases, this may be enough to restore functionality. Interference can also be caused by various electronic devices operating in the immediate vicinity.
2. If this does not help, you need to follow these steps. You need to try how the individual buttons work . If none of them work, you need to change the batteries. Sometimes, when the batteries are running low, a notification will appear on the TV screen. For charging, it is usually necessary to change the batteries. If the remote control is charged using solar panels, it must be placed in a well-lit area to restore functionality.
3. There is another way to check. If you look at the remote control through your smartphone’s camera , you may see a flickering red light when you press the button. If so, then the device is OK. Otherwise, it needs fixing.
4. In modern TV models, a service mode may be provided . If it is set, then this can serve as an obstacle to switching channels. In this case, it is necessary to check which operating mode of the remote control is set and, if necessary, disable it.

Sometimes it may be that the remote control is working, but the TV does not respond to it correctly. For example, if the wizard has a similar working remote control, you can check if it works with the user’s TV. If everything is in order, the most likely cause is that the remote control has lost its operating frequency. In such a situation, it is necessary to set it again correctly. This can be done using the settings of the TV receiver. To do this, you must enter the desired value when setting the corresponding parameter. It should be borne in mind that the operating frequency may differ in different TV models. Data for a specific brand or modification can be found on the website of the TV manufacturer.
If you call the wizard to solve the problem, he will be able to see the real frequency of the signal using an oscilloscope. If necessary, he will perform all the necessary actions to restore the device to working capacity. When you turn on the TV, it may not turn on, but the indicator starts blinking. This may indicate damage to the photodetector. In such a situation, it is necessary to replace it yourself, or call a specialist for repair. Another cause of this problem may be a malfunction of the control board. It is not possible to diagnose it on your own. In this case, the only way to solve this problem is to contact the service center.

Some Tips

When working with the remote control, sometimes non-standard situations may occur, which the user should be aware of. Here are some of the most common cases:

1. Philips TVs may have automatic signal recovery . To do this, it is enough to simultaneously press two buttons: “program” and “volume”.
2. There are models of remote controls that can be used to control various devices . To implement this feature, they have corresponding switches. If the TV does not turn on, you need to check in which mode it works. If necessary, you just need to switch it as needed.
3. Some remote control models provide the ability to configure using a mobile application . In this case, if the device is not working, it is enough to check the settings and restore them.

Sometimes it happens that some of the buttons work, and some do not. Often the cause of this situation is careless handling of the device. For example, it can be tea spilled on the remote control. In such a situation, the following steps should be taken:

1. It is necessary to unscrew the screws holding the remote control and disassemble it.
2. They clean the board, rubber lining and covers. Do not use toothbrushes or similar tools. This is due to the fact that the conductive layer can be erased in this way.

   

3. After that, it is necessary to dry the parts completely. This usually takes no more than an hour.

Sometimes the cause of problems with the key is the lock of the remote control. It is disabled using a set of code combination keys. It is usually listed in the user manual. If it is not possible to read it, the necessary information can be obtained on the manufacturer’s website.