What does a scrambled channel on Telecard mean and how to fix the error

What does a scrambled channel on a
Telecard mean and how to restore the broadcast of satellite channels.

Scrambled channel message (scrambled channel, scramble) – what is the essence of the message

When displaying
Telecard channels , you may receive a message that they are scrambled. This means they are encrypted and cannot be shown. Decryption usually occurs when they are paid, and the user inserts a card confirming this into the CAM reader.

In some cases TV broadcasts cannot be shown because the equipment is set incorrectly. However, in some cases the message in question may be issued even in the absence of such reasons.

How to interpret

When there is a message about a scrambled channel, first of all, you need to establish the reason for what is happening. One of the most likely causes is a faulty console. To fix this, you need to do the following:

1. First you need to remove the access card.
2. Then you need to turn the console over and remove the rubber feet. The screws under them must be unscrewed.

3. You need to remove the cover and open access to the board.

4. To remove the board, unscrew three screws and two nuts from the LNB in ​​and out connectors.

5. Now you need to solder and change all capacitors, the value of which is 16v 100. They need to be replaced with 16v1000uF or 25v1000uF.
6. You need to check other capacitors for blisters. If they are found, a replacement will be required.

7. Assembly is carried out in the reverse order.

After this, scrambled channels should no longer be reported. However, in most cases there may be other reasons for problems with TV shows, which are detailed below.

Why Telecard writes a scrambled channel – other reasons that block channels

If you can’t watch Telecard programs, then you need to figure out what caused this. After that, it will be possible to take appropriate measures to correct the situation. The following reasons may lead to the termination of the show.

Receipt of payment

When showing TV channels, the viewer uses a certain tariff. In order to gain access, he must have no debts. If he forgot to deposit the required amount, then this may cause it to be impossible to view. In such a situation, you need to check payments and eliminate debts, if any.

Weather

Clear weather is required to receive satellite signals. However, one can hardly hope that it will last throughout the year. If there is bad weather in the yard, then this usually leads to problems during the show. This can happen during heavy rain, during snowfall, during heavy fog, and in some other cases. When viewing a coverage map, the user must remember that the data shown is based on clear weather.

Connection error

Even if the antenna is finely tuned to the signal source, connection problems may prevent normal viewing. Here we are talking about the fact that the connectors or
cables may be damaged. The cause of a poor display may be a loose cable connection. For example, if it moves a little in bad weather, this may be a sufficient reason for problems.

TV settings

In order to ensure high-quality signal reception, the TV must work with the correct settings. For example, you need to correctly specify the source of the signal. If the wrong port is specified here, then the TV show will not be displayed.

Checking the map

When watching satellite TV, the viewer chooses a tariff and pays for it. After that, he must confirm this when viewing. To do this, you need to insert the card received from the provider into a special slot. After the information from it is read by the device, the TV channels will be opened for viewing. However, sometimes it may happen that for some reason the information from the card is not available. This will lead to the inability to use the satellite broadcasting of the Telecard.

Company notices

Broadcasting parameters of Telecard channels may change over time. Users are always warned about this so that they can change the corresponding settings properly. If a person does not pay due attention to the messages they receive, they may miss them and not make the necessary changes. To avoid this, just look at the notifications and take them into account in the future.

What to do, how to fix the display error

If it was raining or there was high solar activity during the show, there is nothing the viewer can do to restore normal signal conditions. In such a situation, it is necessary to wait for the time when the weather improves. If she was the only cause of the problem, then soon it will be possible to watch TV shows in good quality. At first glance, problems with the connection to the antenna may be considered an unlikely cause for signal loss. However, this cause is easy to check and easy to eliminate. It is necessary, by means of a visual inspection, to make sure that there are no visible damages on the cables and connectors, and also to check how well they are connected.

It should be borne in mind that the connectors may gradually oxidize during prolonged use, which degrades the quality of the connection. Sometimes pollution leads to problems. In this case, carefully clean the surface before reconnecting.

You need to make sure that the TV settings are correct. It is necessary, in particular, to check which signal source was indicated. It is necessary that the port corresponding to the display from the satellite dish be specified in the settings.
Telecard setup[/ caption] When setting the parameters in the settings, you need to use the TV remote control. What to do if the channels are not shown on the Telecard: https://youtu.be/MY9V5KmGCZc One of the possible causes of the problem may be the insertion of the card on the wrong side. It must be remembered that it must be placed in the appropriate slot chip first. If all the same it is not readable, then you need to repeat the insertion again, carefully doing the necessary steps. If the card does not work, you need to contact the company’s support service specialists.